News Center

Maintenance and maintenance of the machine's full-automatic mask machine before going to work will increase productivity

2020-05-20
The impact of the epidemic has led to the development of the mask market industry, and the fully automatic folding mask machine has been welcomed by many manufacturers in the production process. So how should the mask equipment be maintained during the production process? The following folding mask machine manufacturers share several maintenance tips for you.

 
Automatic mask machine
Automatic mask machine maintenance:
 
(1) Daily routine inspection of equipment and make inspection records;
 
(2) Smooth the smooth points according to the rules before starting and during work;
 
(3) Always check the entire system for leaks;
 
(4) The bearing is made of smooth grease, which is changed every 1-2 years;
 
(5) filter;
 
(6) Refer to the corresponding manual for the maintenance of the mask machine.
 
1. Appearance:
 
The masks produced by our equipment are to be worn on the face, and some medical masks need to be brought into the operating room, so all the mask production needs is to keep the equipment clean and tidy, and arrange to turn off the power equipment workbench after the day For cleaning, use alcohol and other disinfectant and volatile cleaning liquid.
 
2. Transmission system:
 
The transmission system of the labor protection mask machine includes motors, reducers, gears, sprockets, chains, belts and other accessories. Check the motor for the presence of dust and other things that affect the heat dissipation. When the gears and sprockets are oiled regularly, there is something attached In the above, whether the tension of the chain is appropriate, whether there is a loose connection between the transmission components of the screw, and whether the lubricating oil of the reducer is enough is that it needs to be replaced once within 1000-1500 hours.
 
3. Electrical system:
 
Check whether the circuit connector of the labor insurance mask machine is loose, the power cord and the signal cord are worn out? Ageing? Loose electrical components? Whether the electrical box is clean and dry, and whether the exhaust fan is working properly.
 
4. Ultrasonic system (including ultrasonic electric box, impact, welding head, connecting wire);
 
Check whether the labor protection mask machine is clean of the ultrasonic system, especially the ultrasonic electric box, shock (ring nengqi), head (expansion) must be dry-cleaned, there is no water accumulation, and the connection line must be strong. Always check the degree of wear of the ultrasonic welding head. Observe the pointer range of ultrasonic electric voltmeter and ammeter.
 
Five, power supply system: (by air filtration system, pipe, cylinder);
 
Air filter cover, check whether the labor protection mask machine has water, air compressor discharge (air compressor discharge: high humidity in the area, discharge to the compressor every day). Check the air pipe and cylinder for leaks, and the position and operation of the cylinder's magnetic sensor.
 
1. Pneumatic system:
 
The air filter cup of the mask machine needs to see whether there is water, and also to the water compressor, and the area with high humidity should be drained to the air compressor every day. Check whether all air pipes and cylinders are leaking. Magnetic sensor orientation and normal operation.
 
2. Ultrasonic system
 
Check whether the system of the ultrasonic mask machine is kept clean, especially the ultrasonic electric box, vibrator (transducer), and welding head must be dry and clean without water, the connecting wire must be firm, and often check the ultrasonic welding head for wear Degree, pay attention to observe the scale of the change of the pointer of the voltmeter and ammeter on the ultrasonic electric box.
 
3. Transmission system
 
The transmission system includes motors, gears, reducers, sprockets, chains, conveyor belts, etc. We must check whether the motor has dust and other things attached to affect heat dissipation, whether the gears and sprockets are oiled, and if there are attachments, they should be cleaned Clean, is the chain tightness appropriate, is there any foreign matter not cleaned, is there any looseness in the connecting screws between the transmission parts, the lubricating oil of the reducer is not enough, usually the machine needs to be replaced once in 1000-1500 hours .
 
Fourth, electrical system
 
Check whether the connectors of the circuit of the mask machine are loose, whether the main power cord and branch signal line are worn and aging, whether the electrical equipment is loose, whether the electrical box is kept in a dry environment, and the exhaust fan is Not normal work etc.
 
V. Appearance
 
Masks are used to wear on the face, and medical masks need to enter the operating room, so the production of masks requires neat cleaning of the mask machine equipment. Every day after work, you need to arrange personnel to shut down the mask machine equipment after power off. Wash the work surface and the plate with masks on it. Note that you can't use water to clean, and use alcohol and other non-toxic and volatile cleaning liquid to clean the equipment.
 
Six, anti-rust
 
Equipment should not stick to corrosive liquids and objects. Sweat can easily cause rusting of equipment parts. If the equipment does not work for a long time, it is necessary to apply anti-rust oil to the transmission system of the mask and parts that are prone to rust.
 
The above is some maintenance knowledge of the equipment provided by the automatic mask machine manufacturer. As long as the maintenance and maintenance of the automatic mask machine are done every day, the life of the mask machine can be greatly improved and the probability of repair can be greatly reduced, bringing greater interest.